Skateboard-bearing lube alternative is an essential part of skateboarding. It is the lubricant that keeps the bearings of the skateboard moving smoothly and effectively.
Without the right skateboard-bearing lube, the skateboard would not be able to perform the tricks that we know and love. All the skateboard bearings need to be lubricated at intervals of time. Even the best skateboard-bearing brands like Arbor, Santa Cruz, sector 9, etc., need to get oily after some time.
What happens when the skateboard-bearing lube gets old?
The skateboard-bearing lube is an integral part of skateboarding, so finding a replacement is essential. This post will help you with the skateboard-bearing lube alternatives.
The best Skateboard bearing lube alternative
- WD 40
- Rubber cement
- Gel lube
- Lube oil
- Motor Oil
- Triflow Lubricant
WD 40
WD-40 is a non-toxic lubricant that is very useful for keeping bearings clean and lubricated. It is also a very effective degreaser and can be used to remove grease from various surfaces.
WD-40 is available in both aerosol and spray form and is excellent for cleaning up surface spills. It can be applied directly to a surface, sprayed onto a rag, and then rubbed into the surface.
Rubber cement
There are several benefits to using rubber cement for skateboard bearings, including cheap rubber cement. Rubber cement is also easy to use and requires no special tools.
Rubber cement can be used in place of the bearings on a skateboard. It can be applied to the skateboard bearings in several ways, including directly onto them.
Gel lube
Gel lube for skateboard bearing can be beneficial for several reasons. First, it is a simple lubricant that can be applied in many ways. It can be used as a spray or a gel, it can be applied to the bearing before it is installed, or it can be applied after it has been installed. It is also relatively inexpensive.
Gel lube for skateboard bearings can also be beneficial because it is biodegradable and will not damage the environment.
Furthermore, the gel lube is easy to apply and works exceptionally well. Gel lube is an excellent lubricant because it is very sticky and will not fall off the skateboard. Gel lube is also very affordable. It is easy to clean and does not attract dirt like other types of lubes.
Lube oil
There are several benefits of using Lube oil for skateboard bearing, including that it is easy to find and inexpensive. Also, it can be easily cleaned with soap and water. In addition, Lube oil is resistant to heat and is resistant to extreme temperatures.
The most significant benefit is that Lube oil contains no petroleum products. This means it is much less likely to cause damage to the bearings.
It will also protect the bearing from getting worn down. Lube oil is also very cheap and easy to use. You can use it in a variety of ways. You can use it for your bearings while you are skating. So You can also use it as a lubricant for your skateboard truck and wheels.
Motor Oil
Motor Oil for skateboard bearings is one of the best things you can do for your skateboard. You should use high-quality motor oil if you are skating on a board with metal bearings. Low-quality motor oil will cause the metal bearings to wear out faster and make the skateboard less efficient.
The best lubricant for skateboard bearings is a 50/50 mixture of motor oil and transmission fluid. Motor oil is the best lubricant because it has a high viscosity index. It also provides the most protection against corrosion.
Transmission fluid has a low viscosity index and does not provide as much protection against corrosion. You should also use a flush kit to clean the transmission if you use transmission fluid as your lubricant.
Tri-flow Lubricant
It’s one of the most effective and efficient lubricants for skateboard bearings. It’s one of the best lubricants for skateboard bearings.
It is inexpensive. So It is environmentally friendly. It doesn’t cause any damage to the environment. And, it will not harm your skateboard bearings. It’s also effortless to apply. You use a spray can spray it onto your skateboard bearings. After that, you can ride away.
Steps to clean the skateboard bearing.
- Remove all the wheels.
- Underside with soap and water.
- Clean the top side with alcohol.
- Apply a coat of oil.
- Apply a light coat of wax.
- Grease.
- Apply shellac.
- A coat of paint.
- Apply a light coat of varnish.
- Lacquer.
- Apply polish.
Here I have explained the step-by-step process of how to clean the skateboard bearings.
Conclusion
we hope that you found this helpful article. We have provided you with a list of the best alternative cleaners for a skateboard bearing.
Our goal is to provide you with all the information you need to make an informed decision about your purchase. Now it’s up to you to use which alternative per your budget and ease of availability.
